Guitar Lessons
HOW TO RE-STRING A GUITAR – THE RIGHT WAY
Let's start off by freshing up those guitar strings. Here's part two of some tips to help you out.
So, you’ve broken a string, or your guitar strings look more like rusty old fence? It’s time to learn how to change them – the right way. There are many pitfalls with re-stringing a guitar that can leave you with an out of tune instrument, or even an injury, so take care and pay close attention.
Firstly, a warning - we’re dealing with wire at very high tension, so be careful. If a string snaps it can cause eye damage or cut through skin.
Ok, the first stage is to loosen the tension on all the strings. I recommend playing the string while you start loosening it, to check that you’re turning the tuning peg the correct way. There’s nothing worse for you or your guitar than assuming you’re loosening a string when you’re actually tightening it until it breaks. I also recommend buying a string-winding tool, which is a great time saver.
STEP 1: ELECTRIC GUITAR
There are two different common types of electric guitars.
a) Fender Type
Most Fender style electric guitars have the string pulled through the bridge, and the end ball on the string holds it in place. When you remove the strings, make sure that you have all 6 of the little ball ends out of the bridge holes. There’s nothing worse than putting a new string in and realizing that there is a string ball stuck in there. You may wish to hold the guitar up to the light and look through the holes to check everything is clear. Ensure you remove all the strings from the tuning pegs, and pull them out of the guitar through the back of the bridge.
b) Gibson Type
When taking the strings off most Gibson style guitars it's easy to see the ball ends of the strings as they are hooked through the bridge on the face of the guitar. Some of the bridges on these style guitars are held in place by the string tension, so it may be better to only replace a few strings at a time, rather than all at once. Place new strings through the appropriate hole (sharp end first) and pull through until the ball of the string is tight against the bridge.
STEP 1: STEEL STRING ACOUSTIC
Steel string acoustics have small plastic pins that hold the strings into the bridge of the guitar. Loosen all the strings and take them off the tuning pegs. Now it’s time to remove the pins and the strings. There are a few different techniques if they don’t pull out easily. If you purchased a string winder, you can use a section of it to pull out the pins.
If you don’t have a string winder, either carefully put your hand in the guitar and push them out from the inside, or use a teaspoon to lever the pins out. Be very careful as you don’t want to scratch your guitar.
You may wish to take the opportunity to clean your guitar and fingerboard now it’s string free. Guitar shops sell different types of guitar and fingerboard cleaning products that you can use with a cotton cloth to make your guitar look and feel like new.
Place your new strings in the appropriate hole and replace the pins.
While you’re pushing the pin down, it’s a good idea to pull on the string to create some tension so the ball of the string locks in place.
Don’t worry if you break one of the pins, they’re easy to replace and you can buy them at most music shops. It might be a good idea to carry a few spares in your guitar case to be prepared. Pete reports that he's yet to break one after 20 or so years, though!
STEP 2: ATTACH THE STRINGS TO THE TUNING PEGS
This is the same for all types of guitars (except classical guitars). The most important thing here is to make sure that the strings are pulled up on the correct side of the tuning peg. Line up all the holes in the tuning pegs so that they’re all facing down the neck of the guitar. Start by pulling one string through the tuning peg, leaving enough slack so you can get several string rotations on the tuning peg.
I like to give the string one rotation around the tuning peg before tightening. This saves you time and also helps to make sure you have enough string slack.
Now hold the string in place with your right hand on the peg so the string cannot slip and then turn the peg ANTI-CLOCKWISE to tighten. On some Gibson-style guitars, the peg is underneath, so turn clockwise to tighten. As you start tightening the string, let the first rotation go above the hole (where the sharp end is), and the rest under the hole. This helps hold the string in place. I like to bend the remaining string upwards so that it’s out of the way, which also helps to avoid the string slipping. It’s a good idea to get several rotations on the peg - a minimum of 2+ wraps for the bass strings and 3+ for the lighter strings - as this will help the string stay in tune.
STEP 3: BRING THE STRINGS UP TO TENSION
I recommend tightening one string at a time. As the string gets tighter, you should start to use a tuner so you don’t go over the pitch you’re tuning to – refer to the tuning lesson in
Pro Guitar Tips for more help. If you’re not sure how much to tighten the string, try playing some notes up the neck and see if the tuner picks the pitch you are aiming for, this helps indicate how far you have to go. Once you get the string to the pitch you’re after, it’s important to stretch it in by pulling on the string, or strumming the guitar really hard. You’ll hear how the string has gone out of tune, so re-tune the string and repeat until the string remains in tune.
Use some small wire cutters to remove the ends of the strings. Be very careful not to cut yourself on the sharp string ends, or scratch your guitar. Leave a few mm on the ends just in case the strings slip.
The last step is all about safety – make sure you pick up all the old strings. They can be deadly for bare feet, and are often hard to see on the floor. Enjoy the bright fresh sound your new strings have, and rock on!
STRING LOCKING GUITARS
Pete was adament that I mention he doesn’t recommend the Floyd Rose locking tremelo style of guitar for beginners. This system locks the strings into place by using small clamps at the bridge and the nut. The concept allows you to use the whammy bar like crazy, and the strings will hold better tuning. However, if you break a string, all the strings go out of tune and they’re much more difficult to change anyway. If you’ve got this style of guitar and need some help changing strings, ask your local guitar shop for some help learning.